Quintett Nano   Floorstanding as in K+T 1/2021

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 89 dB
  • size (HxWxD): 1000 x 160 x 376 mm
  • frequency range (-8dB): 50 - 21000 Hz
  • crossover frequency(s): 500,29 Hz
  • speaker type: bass reflex

Quintett Nano is a three way floorstanding speaker.

Quintett Nano is a bass-reflex cabinet loudspeaker with drivers of Visaton .

The kit is delivered with the following drivers:
- a Visaton FRS 5X, 8 Ohm full range driver
- a Visaton W100 S, 4 Ohm mids driver
- four Visaton W100 S, 4 Ohm woofers

The loudspeaker has been developed by Holger Barske and Thomas Schmidt.

The crossover consists of:
- a 2nd order high-pass filter (12 dB per octave slope) for the full range driver.
- a band pass consisting of a 2nd order high pass filter (12 dB per octave slope) and a 2nd order low-pass filter (12 dB per octave slope) for the mids-woofer.
- a 2nd order low-pass filter (12 dB per octave slope) for the four woofers.

The frequency response of this speaker is nearly linear.

The decay spectrum (waterfall spectrum) shows a decelerated swing-out behaviour in the mid-range.

At low volume, i.e. 80 dB at 1 m, the nonlinear distortions are below 0,8% above 200 Hz and doesn't exceed 1,2% at 90 dB at 1 m between 300 and 15000 Hz.

Our kit consists of

  • Visaton FRS 5X, 8 Ohm
  • 5x Visaton W100 S, 4 Ohm
  • Bass reflex tube BR15.34, black
  • PE sealing tape, 5x2 mm, 7.5 m
  • 2x Damping Sonofil 100 x 35 cm for 20 litres
  • 0,25x Foam N25, 97,5x49x4 cm, black
  • Binding Post PK31, gold plated (one pair, red and black)
  • 4m Speaker cable 2x1.5 mm2, transparent
  • 3,5x Visaton Countersunk screws 3.5x25, 8 pcs
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 3.9 μF; / 400 Vdc
  • JB, electrolytic capacitor, bipolar, 330 μF/50 Vdc
  • JB, electrolytic capacitor, bipolar, 82 μF/100 Vdc
  • Mundorf, electrolytic capacitor, unetched, 56μF / 50 Vdc
  • JB, electrolytic capacitor, bipolar advanced, 8.2 μF; / 50 Vdc
  • JB, electrolytic capacitor, bipolar advanced, 10 μF; / 50 Vdc
  • Mundorf air core coil L140, 2.2 mH/0.46 Ohm
  • 0.7 mm air core coil, 0.39 mH/0.49 Ohm
  • 0.7 mm air core coil, 0.56 mH/0.55 Ohm
  • 0.7 mm air core coil, 3.3 mH/1.75 Ohm
  • Mundorf H core coil H71, 10 mH/0.87 0hm
  • ceramic resistor 4.7 Ohm/20 Watt
  • Metal-oxide resistor, 10W 2.2 Ohm (red-red-gold)

Kit without cabinet, price per speaker   EUR 343,00 excl. VAT: € 288.24 / $ 311.29

The mounting ring for the Visaton FRS 5 X is not included in the kit

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Visaton FRS 5X, 8 Ohm are of type polypropylen (MKP) ClarityCap ESA 250 V.

  • ClarityCap PWA capacitor 18 μF; / 160 Vdc
  • ClarityCap PWA capacitor 56 μF; / 160 Vdc
  • ClarityCap ESA capacitor 3.9 μF; / 250 Vdc
  • JB, electrolytic capacitor, bipolar, 330 μF/50 Vdc
  • JB, electrolytic capacitor, bipolar, 82 μF/100 Vdc
  • Mundorf baked varnish air core coil BL71, 0.39 mH/0.51 Ohm
  • Mundorf baked varnish air core coil BL71, 0.56 mH/0.64 Ohm
  • Mundorf baked varnish air core coil BL71, 3.3 mH/1.75 Ohm
  • Mundorf baked varnish air core coil BL140, 2.2 mH/0.46 Ohm
  • Mundorf H core baked varnish coil BH71, 10 mH/0.87 0hm
  • ceramic resistor 4.7 Ohm/20 Watt
  • Metal-oxide resistor, 10W 2.2 Ohm (red-red-gold)

Kit with high-end-crossover without cabinet, price per speaker   EUR 391,00 excl. VAT: € 328.57 / $ 354.86

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).

  • Audaphon MKT CAP 4.7 μF; / 160 Vdc
  • 0.7 mm air core coil, 0.39 mH/0.49 Ohm
  • ceramic resistor 6.8 Ohm/20 Watt

Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 8,00 excl. VAT: € 6.72 / $ 7.26

universal PCB

If you prefer to mount the crossover components on a 159 x 127 mm universal PCB instead on wood:
Universal PCB RA160, order no.. I-2766, price per unit:   EUR 5,10 excl. VAT: € 4.29 / $ 4.63
We recommend one board per kit (two boards for a speaker pair)


Home   Klang+Ton Overview