Sculptor   Floorstanding as in K+T 5/2019

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 88 dB
  • size (HxWxD): 1500 x 280 x 410 mm
  • frequency range (-8dB): 30 - 38000 Hz
  • crossover frequency(s): 210, 1900 Hz
  • speaker type: closed box
Enlarge

Sculptor is a three way floorstanding speaker.

Sculptor is a closed-cabinet loudspeaker with drivers of Audaphon and Wavecor.

The kit is delivered with the following drivers:
- a Audaphon APR 1.0 ribbon-tweeter
- two Wavecor WF152CU14 mids drivers
- four Wavecor SW223BD02 woofers

The loudspeaker has been developed by Dennis Frank and Daniel Gattig.

The crossover consists of:
- a 3rd order high-pass filter (18 dB per octave slope) for the tweeter.
- a band pass consisting of a 2nd order high pass filter (12 dB per octave slope) and a 2nd order low-pass filter (12 dB per octave slope) for the mids-woofers.
- a 2nd order low-pass filter (12 dB per octave slope) for the woofers.

The frequency response of this speaker is perfectly linear.

The decay spectrum is nearly perfect.

At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are below 0.3% above 500 Hz and doesn't exceed 0.4% at 95 dB at 1 m between 300 and 15000 Hz.

Our kit consists of

  • 2x WF152CU14, Wavecor Mid/Woofer, 8 Ohm, paper cone, BD, phase plug
  • 4x Wavecor Subwoofer SW223BD02, die cast, 4 Ohm
  • Audaphon Aluminium Ribbon Tweeter APR 1.0
  • 3x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • 4x Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK28 I Ni, nickel plated (one pair, red and black)
  • 5m Speaker cable 2x1.5 mm2 black/red
  • Pan screws 3.5x17 black, torx, 8 pieces
  • 4x Pan screws 4x20 black, torx, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.

  • Audaphon MKP CAP Superior 0.33 μF / 400 Vdc
  • Audaphon MKP CAP Superior 2.2 μF / 400 Vdc
  • Audaphon MKP CAP Superior 3.9 μF / 400 Vdc
  • Audaphon MKP CAP Superior 8.2 μF / 400 Vdc
  • Audaphon MKT CAP 4.7 μF / 160 Vdc
  • Audaphon MKT CAP 33 μF / 160 Vdc
  • Mundorf, electrolytic capacitor, etched, 150 μF/63 Vdc
  • Mundorf, electrolytic capacitor, unetched, 82μF / 50 Vdc
  • 1.4 mm air core coil, 0.82 mH/0.26 Ohm
  • 0.7 mm air core coil, 0.68 mH/0.70 Ohm
  • Mundorf baked varnish air core coil BL71, 0.068 mH
  • Audaphon M core coil M14, 4.7 mH/0.24 0hm
  • Mundorf H core coil H71, 3.3 mH/0.47 0hm
  • Mundorf H core coil H71, 4.7 mH/0.46 0hm
  • 2x Metal-oxide resistor, 10W 4.7 Ohm (yellow-violet-gold)
  • Metal-oxide resistor, 10W 6.8 Ohm (blue-grey-gold)
  • 2x Metal-oxide resistor, 10W 10 Ohm (brown-black-black)

Kit without cabinet, price per speaker   EUR 2580,00 excl. VAT: € 2168.07 / $ 2341.51

Kit with high-end crossover

The high-end kit is delivered with baked varnish air core coils on important parts of the crossover for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered. The capacitors for the Audaphon APR 1.0 are of type polypropylen (MKP) Clarity-Cap CSA 630 V and 250 V.

Kit with high-end-crossover without cabinet, price per speaker   EUR 2677,00 excl. VAT: € 2249.58 / $ 2429.55

Kit with high-end crossover

The high-power kit is equipped with high-power coils in series to the woofers, and contains high-quality capacitors at essential points (in front of the mid-range loudspeakers, for example: popypropylen film capacitors).

Kit with high-end-crossover without cabinet, price per speaker   EUR 2742,00 excl. VAT: € 2304.20 / $ 2488.54

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 10,50 excl. VAT: € 8.82 / $ 9.53

universal PCB

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 220x155 mm, order no. I-8805002, price per unit:   EUR 11,80 excl. VAT: € 9.92 / $ 10.71
We recommend one board per kit (2 boards per speaker pair)

Measurements

measurmentsMeasurements on this speaker

Pictures

PhotosPictures of this loudspeaker

Home   Klang+Ton Overview